A DD-WRT compatible router. Flash it with the appropriate DD-WRT factory image. A subscription to a VPN service that supports OpenVPN. I recommend reading this guide and then using the comparison chart on the same site to inform your decision. Enable VPN. Once you have a VPN subscription, find the service's OpenVPN configuration guide. If it's

Un article sur la façon d'installer le micrologiciel DD-WRT sur un routeur peut être trouvé ici. Ce tutoriel montre comment configurer une connexion OpenVPN sur votre routeur DD-WRT en utilisant l'interface client OpenVPN. Il a été fait en utilisant cette configuration : Firmware : DD-WRT v3.0-r40900 std (09/04/19) Le matériel : Linksys As far as how you configure the router wrt the WAN (DHCP vs. static IP, dynamic vs. static DNS, etc.) is totally irrelevant to the OpenVPN client. You should be able to connect the OpenVPN client even if you used a default configuration w/ the WAN. Only issue (as is always the case, whether using a VPN or not) is making sure your VPN router's local network and the upstream/primary router are Both sites have a WRT54GS loaded with DD-WRT v23 SP1 Final VPN. I have read the wiki and enabled the OpenVPN Server on the remote WRT. I have also configured the Hub WRT to connect to the DDNS name of the remote WRT. My question is the configuration. The wiki refers to two seperate networks 192.168.x.x and 10.0.100.x. I would like to know what both networks refer to and how to configure each Router to Router Bridged Configuration Alternative (Hardware VPN) (for hardware "like" vpn access for multiple computers or appliances) This is a quick and dirty guide to creating a VPN between (2) DD-WRT v24 SP2 routers (both flashed with VPN version). 1. Open the DD-WRT control panel for your router (typically this can be accessed via a web browser by entering 192.168.1.1 or 192.168 .0.1 instead of url) 2. In the DD-WRT panel go to "Services" → "VPN" Set the "Start OpenVPN client" option to "Enable" 3. Enter the following: S erver IP/name to the hostname of the server you wish to connect Configuring an OpenVPN Server in DD-WRT — 3. I was contacted about my previous attempts to configure OpenVPN in DD-WRT. I never completed the project. The contact person offered a possible solution and asked me to test. This person was using DD-WRT version v3.0-r31899 std (04/24/17) on a Linksys WRT-1900ACS. I was using v3.0-r30826 std (11/01 J' avoue que je désespérais un peu de pouvoir publier ce tutorial d' installation d'une connexion en OpenVPN avec le firmware DD-WRT sur mon Linksys WRT54-GL.

How to configure the OpenVPN client on DD-WRT routers. Note: Only the new DD-WRT firmware support this method. The following configuration was tested on a 

– Cela est rapide à configurer, la vitesse est stable ainsi que la configuration. StrongVPN, grâce à leur script, offre une solution simple et efficace. Si vous voulez un routeur , avec un firmware DD-WRT, en OpenVPN, profitez de StrongVPN et de son OpenVPN à $10 par mois (Moins de $100 à l’ année) .

29/03/2010

Initial DD-WRT Setup and Important Notes Please check and consider the following before setting up your VPN connection in DD-WRT: If you are running a router-behind-router configuration, you will want to make sure your DD-WRT router is on a different subnet than any other router/modem on your network. This can be done by going to Setup/Basic 05/09/2016 J'ain installé un firmware DD-WRT SP23 vpn sur mon WRT54GL, et je n'ai que la configuration de la partie cliente dans l'interface web. J'ai cru comprendre que l'on pouvait proceder à l'installation / paramétrage d'openvpn server directement en shell (telnet ou ssh) mais je ne trouve aucun tuto ou quelque chose qui résume comment procéder. On DD-WRT, go to the Administration->Services and set PPTP server to active, save the changes, then set the IP of router (192.168.1.1) for the server IP, and under Client IP(s) set a range for connections. (192.168.1.20-29 for example of a ten client set up) Under Chap Secret put in username * password * for example: testmachine * password1234 * ( The "*" are NOT a Placeholder, they must be This page was last modified 23:39, 4 January 2019. This page has been accessed 80,827 times. Veuillez confirmer que DD-WRT est pris en charge par votre routeur. Saisissez la marque et le modèle de votre routeur dans le champ de recherche du site web DD-WRT et appuyez sur entrée.; Pour installer DD-WRT à l'aide de PPTP, suivez les instructions pas-à-pas fournies sur le site DD-WRT. L'installation de DD-WRT sur votre routeur doit être faite avec soin. Open the OpenVPN configuration you have downloaded in Step 3 in any text editor file of your preference (preffered WordPad or Notepad++ as regular notepad does not have the correct formatting. 6. When you open the .ovpn file of the server you chose to use (in our case, us936_nordvpn_com.udp.ovpn ) with a text editor, you should see the part of the file (do NOT copy the and tags):